Skip to main content

NFPA 72 annual testing · Trouble and supervisory signals · Restarting systems that went dark

Your fire alarm is due for its yearly test. Or the panel won't stop beeping. Either way, the work follows NFPA 72, and the office that checks it depends on your building's city, because San Bernardino County Fire covers many cities and some others run their own fire departments. We do the testing, answer the trouble calls and make the repairs.

What gets tested each year

NFPA 72 requires an inspection and test at least once a year. Some devices need it more often. On a typical annual visit the technician works through every part of the system: smoke and heat detectors, manual pull stations, sprinkler waterflow and valve tamper switches, horns and strobes, and the control panel with its standby batteries. Each device has to send the right kind of signal. A pull station should report as an alarm. A closed sprinkler valve should come in as a supervisory signal and a cut wire as a trouble signal, and all three should reach your monitoring company. Old batteries are a common failure. Devices that don't pass get written down so they can be repaired or replaced.

County Fire city or city fire department?

San Bernardino County Fire's Office of the Fire Marshal is the district's inspection and regulatory arm. Its headquarters is at 598 S. Tippecanoe Ave. in San Bernardino, and the cities it serves include Adelanto, Fontana, Grand Terrace, Hesperia, Needles, San Bernardino, Twentynine Palms, Upland and Yucca Valley. Other cities have their own agency. Rancho Cucamonga is one: its Fire Protection District has a Prevention Bureau, under its own fire marshal, that runs high-hazard Fire Code inspections in that city. Not sure? Call the fire marshal's office for your address before the test and ask what they expect to see. The San Bernardino County Fire Office of the Fire Marshal site is a good first stop.

In February 2023 the District adopted a fire code built on the 2022 California Fire Code with local amendments, so if you're planning new devices, a panel replacement or a tenant remodel, confirm the edition and amendments in force with the fire marshal before design starts. Ask first.

Trouble lights, supervisory signals and dark panels

A trouble signal means the system found a fault in itself, such as an open circuit, a ground fault or lost power. A supervisory signal usually means something the alarm watches has changed, like a sprinkler valve that was turned off. Neither one is a fire. Both need a technician. If you silence the panel and walk away, the building has gaps in its protection until someone finds the cause.

A system that has been switched off or unmonitored for a long stretch takes more than a reset, because batteries die, devices get disconnected or covered, and the monitoring account may have been closed in the meantime. Our case study on reactivating a fire alarm that sat dormant for two years in Rancho Santa Margarita shows how that kind of job goes.

Who does the work

California work for 1 Pro Fire is done by Hedrick Fire Protection. Hedrick holds C-10 (electrical) and C-16 (fire protection) contractor licenses. It is also licensed by the California State Fire Marshal under Title 19 for portable extinguisher service and for inspection, testing and maintenance of water-based systems such as sprinklers. That puts your alarm and the sprinkler system it monitors with one contractor. Send us the address and what's due. Reach us at (909) 219-9411 or socal@1profire.com.

Related services and nearby pages

Fire alarm questions

How often does a fire alarm need to be tested?

At least once a year under NFPA 72. Some devices run on a shorter schedule.

Who checks my fire alarm in San Bernardino County?

It depends on the city. Many cities are served by San Bernardino County Fire's Office of the Fire Marshal, while cities such as Rancho Cucamonga have their own fire prevention bureau.

Can you test the sprinkler switches tied to my alarm?

Yes. We work on both the alarm side and the water-based side, so waterflow and tamper switches can be checked from the device all the way to the panel.

My panel shows a trouble light. What should I do?

Write down the message on the panel display and call us. A trouble signal means part of the system may not work.

Get a fire alarm quote in San Bernardino County

Annual test, repair or panel restart.

(909) 219-9411 or socal@1profire.com